matrix alloy造句
例句與造句
- Preparation for foil material of new nickel matrix alloy
新型高電阻率鎳基合金箔材研制 - A better strengthening effect on am50 by adding re has a relation to the content of zn in the matrix alloy
稀土對am50合金力學性能改善的效果碩士學位論文要比azgl好，這與基體合金中zn的含量有關。 - Microscopic analysis of the abrasion surface indicated that the wear mechanism of composites and matrix alloy included sticking abrasion and grindrng - particle abrasion on the materials
磨損表面微觀分析表明，復合材料的磨損過程是粘著磨損和磨粒磨損兩種機制共同作用的結果。 - The hardness of the parts made of composits was higher than that of the parts made of the matrix alloys . but the hardness of both kinds was higher than their ingots respectively
復合材料壓鑄件的布氏硬度比基體合金壓鑄件的布氏硬度高，兩類壓鑄件的布氏硬度分別高于相應鑄錠的布氏硬度。 - The composite containing 8vol % sic particles and the matrix alloy were die - cast into parts and particles reinforced aluminum matrix composites parts were first successfully manufactured by die - casting in domestic
本文還對復合材料進行了壓鑄試驗，成功制備了國內首批sic顆粒增強鋁基復合材料的壓鑄件。 - It's difficult to find matrix alloy in a sentence. 用matrix alloy造句挺難的
- Based on the literature analysis of al matrix in - situ composites by reaction synthesis , it is found that in - situ reaction synthesis processed can ameliorate wettability between reinforcement phase and al matrix alloys and strengthen interfacial bonding and improve mechanical properties of al matrix composites
對反應生成的原位鋁基復合材料的研究表明，原位反應合成技術可以改善強化相與基體鋁合金之間的潤濕性，強化界面連接，提高材料的綜合機械性能。 - The high - temperature properties of ti3al matrix alloy can satisfy the request of the exit temperature of the areoengine compress . but the room temperature plasticity of ti3al matrix alloy is very low , hard to shape , and manufacture ' s cost is very expensive
Ti _ 3al基合金高的高溫性能可以滿足飛機發動機壓氣機出口溫度的要求，但由于ti _ 3al基合金室溫塑性差，成形困難，制造成本高；而tc11兩相鈦合金可以在500以下溫度長時間工作，用于壓氣機盤已比較成熟。 - The results showed that sic particles dispersed uniformly in the composites , that the composites " hardness increased with the increasing volume fraction of sic particles , and that the composites had the outstanding wear resistance properties that were superior to the matrix alloy
結果表明， sic顆粒在復合材料中分布均勻；復合材料的硬度隨sic顆粒體積含量的增加而增加，且比基體合金的硬度高； sic顆粒增強鋁基復合材料具有優良的耐磨性能，且優于基體合金。 - What ' s more , the application of tc11 two phase alloys to the compress disk of areoengine alredy is relatively mature , and tc11 alloy may work safely for very long time below 500 c . ti3al matrix alloy and ( a + b ) two phase alloy is connected by weld . the request of the temperature and stress can be satisfied by dual alloy disk with isothermal forged ( or hot die forging )
選用ti _ 3al基合金tac - 1b和tc11兩相鈦合金用焊接工藝連接起來，通過熱模鍛或等溫鍛鍛造和不同的變形熱處理制度，制造出雙合金盤可以滿足溫度、應力對盤件的要求。 - The results of the hardness test showed the composites " hardness increased with the increasing volume fraction of sic particles . results of the wear tests showed the composites had the outstanding wear resistance properties , especially in lubricated sliding case , the wear resistance properties of the composites were superior to the matrix alloy over one or two orders of magnitude
結果表明，復合材料鑄錠中， sic顆粒分布均勻；材料的硬度隨sic顆粒體積含量的增加而增加； sic顆粒增強鋁基復合材料具有優良的耐磨性能，在油潤滑條件下，復合材料的耐磨性能比基體合金高一至兩個數量級。